1、功能说明
     1、GTIMA7的CH1、CH2、CH3、CH4分别触发ATIM1_CH1、ATIM2_CH1、GTIMB1_CH1、GTIMB2_CH1输出，
          ATIM1_CH1与ATIM2_CH1、GTIMB1_CH1、GTIMB2_CH1相位差分别为90，180，270

2、使用环境
    软件开发环境：KEIL MDK-ARM V5.34
    软件开发环境：IAR EWARM 8.50.1

    芯片支持：
        N32H730  
        N32H735   
        N32H735EC
        N32H760
        N32H762
        N32H765
        N32H765EC
        N32H785
        N32H785EC
        N32H787

3、使用说明
    系统配置；
        1、时钟源：HSI+PLL
        2、系统时钟频率：
            M7核: 600MHz
        3、端口配置：
			PA8选择为ATIM1的CH1输出
			PC6选择为ATIM2的CH1输出
			PA2选择为GTIMB1的CH1输出
			PB8选择为GTIMB2的CH1输出
        4、TIM：
			GTIMA7的CH1、CH2、CH3、CH4分别触发ATIM1_CH1、ATIM2_CH1、GTIMB1_CH1、GTIMB2_CH1输出
    使用方法：
        1、编译后打开调试模式，用示波器或者逻辑分析仪观察ATIM1_CH1、ATIM2_CH1、GTIMB1_CH1、GTIMB2_CH1的波形
        2、程序运行后，ATIM1_CH1与ATIM2_CH1相位差为90，ATIM1_CH1与GTIMB1_CH1相位差为180，ATIM1_CH1与GTIMB2_CH1相位差为270。


4、注意事项
    无
    
1. Function description
     1. CH1, CH2, CH3 and CH4 of GTIMA7 trigger the output of ATIM1_CH1, ATIM2_CH1, GTIMB1_CH1 and GTIMB2_CH1, respectively.
          The phase difference between ATIM1_CH1 and ATIM2_CH1, GTIMB1_CH1, GTIMB2_CH1 is 90, 180, 270 respectively

2. Development environment
    Software development environment: KEIL MDK-ARM V5.34
    Software development environment: IAR EWARM 8.50.1

    Supported chips:
        N32H730  
        N32H735   
        N32H735EC
        N32H760
        N32H762
        N32H765
        N32H765EC
        N32H785
        N32H785EC
        N32H787

3. How to use
   System Configuration:
        1. Clock source: HSI+PLL
        2. System Clock frequency: 
            M7 Core:     600MHz
        3. Port configuration:
			PA8 is selected as the CH1 output of ATIM1
			PC6 is selected as the CH1 output of ATIM2
			PA2 is selected as the CH1 output of GTIMB1
			PB8 is selected as the CH1 output of GTIMB2
        4. TIM:
			CH1, CH2, CH3 and CH4 of GTIMA7 trigger the output of ATIM1_CH1, ATIM2_CH1, GTIMB1_CH1 and GTIMB1_CH1, respectively
    Instructions:
        1. After compiling, open the debug mode and observe the waveforms of ATIM1_CH1, ATIM2_CH1, GTIMB1_CH1 and GTIMB2_CH1 with an oscilloscope or logic analyzer.
        2. After the program is run, the phase difference between ATIM1_CH1 and ATIM2_CH1 is 90, the phase difference between ATIM1_CH1 and GTIMB1_CH1 is 180, 
            and the phase difference between ATIM1_CH1 and GTIMB2_CH1 is 270.
4. Attention
    None

